The traditional race wires prevent damage to wires or even propeller strikes from dropping you out of the air, while also making motor swaps super fast and easy without the need to open up your quad to access your 4in1 ESC or AIO board. that is a kind of progress of professional development. However, there’s still an extra soldering job needed to be done if you need to mount RGB LEDs on it.
That’s why iFlight release this RGB 10 LED 3535 Multi-Colors Race Wire. It is designed with 2oz copper and a 2 layer board which provide virtually no difference in resistance and weight difference when compared to previous original Race Wire but liberates you from extra soldering RGB LED strips job, which is perfect for frames with slim arms. You also have access to multi-colors on one board, no more picking one color LED like before.
This race wire is the perfect upgrade for your racing or freestyle rig.
- 10 pcs 3535 RGB multi-colors led strips
- Support 40A Constant Current
- PDB and RGB led strips to work independently
- 2oz 2layer copper board
- Dimension: 45*8*4mm
- Input Voltage: 5V DC
- Comes in a set of 4 individual boards
- LED color: Multi-colors
- Weight: 2.2 grams per pc
How to use:
*Connect the motor cables of 4 IN 1 ESC and cables of the motor to the soldering pad of the Race Wire separately
*Connect the Race Wire to the 5V power source (Pin 5V+ & GND)
*IN connected to signal cable (Multi-colors programmable)
*O connected to the next Race Wire then they’re in series.
*Attention: isolation between the carbon and the board is still required.
4x RGB 10 LED 3535 Multi-Colors Race Wire
● It is compatible with the functions of the traditional active buzzer and synchronized with the flight control
● When the flight control is normally connected, if the main battery in the flight is powered off, it can still automatically
emit 110 dB of drip sound after 30 seconds of power failure, and the LED will emit white light, and the sound is
louder than the general buzzer
● Press and hold the release button for more than 2 seconds, the JHE42B - S buzzer turns off the sound
Dimension and Weight
Product weight: 0.0050 kg
Package weight: 0.0080 kg
Product size (L x W x H): 1.80 x 1.70 x 1.50 cm / 0.71 x 0.67 x 0.59 inches
Package size (L x W x H): 3.00 x 3.00 x 2.00 cm / 1.18 x 1.18 x 0.79 inches
1 x Buzzer, 1 x Wire
De Runcam Control Adaptor is ontzettend handig als je even snel je Camera instellingen(Runcam) wil wijzigen zonder al teveel moeite.
Deze RunCam Control Adapter is compatible met diverse flight controllers:
• Betaflight 3.3 en hoger
• ButterFlight 3.4 en hoger
• Cleanflight 2.2 en hoger
The HellGate FPV Buzzer is a fully automatic acoustic alarm for your miniquad or any other kind of aircraft that could suffer from battery ejection after a crash.
With the HellGate Buzzer you don’t have to be afraid anymore.
After the main battery is accidentally disconnected, it will activate the alarm state and after one minute, if the battery is not reconnected it will start beeping.
The acoustic alarm will last for more than 3 days. I can also switch itself automatically into “eco” mode (after 3 days of active alarm) and continue to beep every 30 seconds for more than 2 weeks.
There is no complicated installation or maintenance process involved.
Simply connect it to a 5V power input, a Ground pin,
and a FC buzzer Ground if you would like to use it as a regular buzzer on your aircraft, since it supports a buzzer passthrough.
To deactivate the buzzer (when you don’t want to fly immediately after disconnecting the empty battery or for transport) you simply connect the battery for a a short amount of time and disconnect it right after. (just touch the plugs for 0.5s to 2s and it will disarm) The buzzer will respond with an appropriate deactivation tone.
2-6S PDB-XT60 W/ BEC 3A 5V & 12V
Input: 7~27V (2~6S LiPo) w/TVS protection
PDB: 4x30A (Max.4x50A), 4 layers*2oz copper PCB
Dual BEC: 5V 3A & 12V 3A
1 x PDB
1 x XT60 plug
4 x M3*7MM Nylon Standoffs
Volt Regulator Mini360 DC-DC Step down Converter 4.75V-23V naar 1V-17V.
Voor gebruik bij bijvoorbeeld het voeden van je VTX zonder storingen in je beeld.
Opgepast bij verkeerd aansluiten, kan blijvende schade opleveren.